20# large diam
20# large diamlongitudinal circumferential continuous pipe and penstock
Continuous pipe is committed to producing all kinds of circumferential seam, and is reformed on the basis of the same specification and model of traditional pipe rolling equipment.
Thick wall coiled pipe is usually higher than dn450. Thick wall coiled pipe is sometimes two welds. Why does this happen mainly because of raw material problems and equipment processing problems? The steel plate with the required width of welded pipe required by the customer is usually not produced by the steel plant, so two plates need to be welded, so the weld will occur. The main problem of thick wall coiled pipe is welding. As long as flaw detection can be carried out, the requirements related to delivery are wider than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector. The longitudinal weld on the same cylindrical part of the coiled pipe shall not be greater than 2. When the coil pipe is butt welded, the corresponding parts shall be flushed to. When the nominal diameter is larger than the inner seal, the bottom seal welding shall be carried out. The surface of the circuit board shall be protected from damage during tube rolling treatment.
.With the dissolution of the steel coil surface, nickel and chromium in the solution will gradually increase. At this time, the solution will gradually lose its polishing ability. In any case, increase the temperature, turn on the current and equalize the force. For the analytical solution, if the iron content exceeds 60g / L and the valence chromium content exceeds, it indicates that the solution has been aged. There are two options for the regeneration of polishing solution and the restoration of polishing ability. When the solution is diluted with water to reduce the acidity impurities such as iron, chromium and nickel can be locally precipitated as salt, and the precipitation at the bottom of the tank can be removed, and then heated and evaporated to remove water, so it is cumbersome to restore the original relative density, which requires a large consumption of energy and time. The other is to replace part of the solution, so as to retain 20% of the old solution and supplement 80% of the new solution. It can be polished with little or no power.
Thick wall coiled pipe sometimes has two welds. Why does this happen? It is mainly due to raw material problems and equipment processing problems. The width of the welded pipe required by the customer is not produced by the steel plant, so the two plates must be welded, so this kind of weld occurs. The main problem of thick wall coiled pipe is welding. As long as the flaw detection can be carried out, the delivery can be carried out. The relevant requirements are broader than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. High cost. Hot rolled thick wall coiled pipe is widely used: oil cylinder, hydraulic pressure, bridge, roller, etc& amp; amp; quot; Compared with seamless steel pipe, thick wall coil has the disadvantages of low cost, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Quality department 3 editing of welding process and welded pipe type thick wall coiled pipe is made of steel plate or steel strip after bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe, deep well pump pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Objective knowledge packaging strategy thick wall steel plate coil - thick wall steel plate coil price thick wall coil is formed by bending steel plate or steel strip, with the electrical model of 031 inspection 8517611 standard, and then made by high-frequency welding and submerged arc welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, deep well pump pipe idler pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe, coil, Q235B coil, Q345B coil, large-diameter thick wall coil, stainless steel coil, L360 coil and 16Mn coil. The inspection is strict and the quality is preferential
.The function of parameters of pipe rolling equipment is improved by 30%, which fills the gap that can not be produced by traditional steel rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 4-100mm. The main materials are q23q3420, 435cimo and 42cimo, 16 manganese and 16 manganese capacity. Generally speaking, cold-rolled sheet can be used for pipe rolling. Product standards: GB / t50205-200, GB / t3092-2001, etc.
The influence of welding process parameters mainly includes two aspects: according to the production characteristics of spiral steel pipe, the welding current is usually smaller for internal welding and larger for external welding. However, under the condition of large welding current, the stirring effect of molten pool is intensified, and the melting amount of welding wire is also the same
The volume of coiled pipe, Q235B coiled pipe, Q345B coiled pipe, large-diameter thin-wall coiled pipe, large-diameter thick wall coiled pipe, stainless steel coiled pipe, L360 coiled pipe, 16Mn coiled pipe and other special products have increased accordingly. With the development of domestic economic situation and the acceleration of welding and casting trend, the advantages of NC cutting have been gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. In industrial production, the thermal cutting of thick wall coiled pipe generally includes gas cutting, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, which improves the machining accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology. 20 old brands, price
Because the coiled steel pipe plays an important role in construction, railway construction and bridge construction, its quality standards are also more important. If you don't understand the quality specifications and standards, it is easy to have an impact. Generally we can purchase from these aspects.
Surface derusting standard: sand blasting derusting on the outer surface of steel pipe shall reach grade SA2 1 / 2 according to the requirements of GB / T 23-2008, at present and the depth of anchor grain on the surface of steel pipe shall be 40-100μ M steel plate rolling circle specification range steel plate rolling circle specification range: for steel pipes with an outer diameter of more than 325mm and a wall thickness of more than 20mm, the large diameter of single weld can reach 1220mm,45# large diameter reel, the wall thickness can reach 80 and the diameter can reach 2020mm.
The inner diameter of 1800mm steel plate coiled pipe elbow is 1800mm, the bending radius is also 1800mm, four bends, the material thickness is 4mm, thick wall rolling pipe has the disadvantages of low cost, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Thick wall coiled pipe is made of steel plate or steel strip by bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe,20# large diameter welded pipe, wire sleeve, idler pipe, deep well pump pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Rolling pipe is committed to producing all kinds of rolling pipes and steel penstocks with circumferential seam and longitudinal ring, and is reformed on the basis of similar specifications and models of traditional rolling equipment. The function of improving the parameters of the rolling and welding steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. Materials mainly include q23 q34 20#, 16 manganese, etc. Product executive standard: GB / t50205-200, GB / t3092-2001, chemical industry, natural gas transportation, pile driving and urban water supply, heating, gas supply and other projects.
Cold rolled thick wall continuous pipe is similar to cold rolled thick wall continuous pipe, with wall thickness of 20mm and outer diameter of 450-3000mm. Steel plate is directly rolled, welded, formed, butted and reinforced. Cold rolled thick wall pipe has the characteristics of short processing time, fast delivery and low cost. Cold rolled thick wall pipe is mainly used for: pipe, billboard, column, etc.
1 carbon structural steel: q215-a, q215-a. & middot; F,Q215-B,Q215-B· F,Q235-A,Q235-A· F,Q235-B,Q235-B· F. Q235-c ordinary carbon steel: B2 BY2 B2F by2f B3 by3 B3F by3f a2ay2 a2f ay2f A3 ay3 A3F ay3f2 high quality carbon steel: 10 15 20 transmission shaft steel 3 low alloy structural steel: 123mn 16Mn 19mn 08ti 10ti15ti4 special purpose steel plates are stacked in the open air to prevent rain from causing steel plates. The oxide scale falling off the surface of steel plates is easy to turn into blocks or clusters and adhere to steel plates or crimping rollers When repeatedly pressed, the coiled pipe forms pit defects.
Generally, the wall thickness of the rolled pipe is 20mm and the outer diameter is 450-3000mm. It is rolled, welded, formed, butted and rolled directly from the steel plate. It has the advantages of short processing time, fast delivery and low cost. The rolled pipe is mainly used for hot-rolled thick wall coils such as pipes, billboard and columns. The thickness of the hot-rolled thick wall coil is generally greater than 20mm and the outer diameter is 450-3000mm. The hot-rolled thick wall coil is rolled under the heating of the steel plate Welding, forming, deburring, defect detection and delivery. Sometimes the wall thickness is relatively thick and secondary heating is required. The feature is that the outer diameter tolerance is small Uniform wall thickness. It is important that the hot rolled thick wall coil will not damage the properties of raw materials. The disadvantages of hot roll thick wall rolling pipe are long processing time and. Hot rolled thick wall coils are widely used: cylinder, bridge roller table, etc.
supply.However, the disadvantages of manual cutting and cutting are also obvious, and the quality of the incision is very poor Big size error There is a great waste of materials The post-treatment process has large processing capacity and poor working conditions. Cutting with a forming machine can greatly improve the quality of the workpiece, but the workpiece must be pre machined. It is not suitable for blanking of single chip small batch and large workpiece. Although the semi-automatic cutting machine reduces the labor intensity, its function is simple and is only suitable for cutting two shapes. Due to the low cost of equipment, the above cutting is easy to operate compared with CNC cutting Easy to operate, so even in some large enterprises, it is still widely used in small and medium-sized enterprises.
Whether the hot coil thick wall pipe rolling machine operates normally and fill oil into the oil hole.
During the plate crimping process, the steel plate can be sandblasted to eliminate the iron oxide scale on the surface of the steel plate and ensure the raw materials on the cylinder surface during the processing process.
.1 carbon structural steel: q215-a, q215-a. & middot; F,Q215-B,Q215-B· F,Q235-A,Q235-A· F,Q235-B,Q235-B· F. Q235-c ordinary carbon steel: B2 BY2 B2F by2f B3 by3 B3F by3f a2ay2 a2f ay2f A3 ay3 A3F ay3f2 high quality carbon steel: 10 15 20 transmission shaft steel 3 low alloy structural steel: 123mn 16Mn 19mn 08ti 10ti15ti4 special purpose steel plates are stacked in the open air to prevent rain from causing steel plates. The oxide scale falling off the surface of steel plates is easy to turn into blocks or clusters and adhere to steel plates or crimping rollers, When repeatedly pressed, the coiled pipe forms pit defects.
The steel plate coil adopts the secondary forming process. When rolling, first bend both ends of the steel plate, and the diameter shall be less than the diameter of the coiled pipe. Then adjust the bed pressure, rolling two to three times steel pipe coiled pipe welding and strengthening the rolling pipe joint, long-term rolling pipe Q235B coil pipe, Q345B coil pipe, large diameter thin wall tube, large diameter heavy wall coil pipe, stainless steel coil pipe, L360 coil pipe, 16MN coil pipe and other brand products, designated products are complete, quality assurance. Then transported to the welding platform for welding.
Application of hot rolled steel pipe: the disadvantage of changing hot rolled steel pipe into seamless steel pipe with fixed specification and model is another major feature of hot rolled steel pipe. In the production process, hot rolled steel pipe has been widely used, bridge construction, engineering column, large drum and so on. Save materials and labor for the above enterprises, reduce production costs, improve the market competitiveness of finished products, and promote the development of enterprises to a certain extent. Continuous pipe is committed to producing all kinds of circumferential seam, longitudinal circumferential continuous pipe and penstock, and is reformed on the basis of the same specification and model of traditional pipe rolling equipment. The function of parameters of pipe rolling equipment is improved by 30%, which fills the gap that can not be produced by traditional steel rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm.