16Mn welded steel pipeAnalysis of the individual characteristics of the market

announcer:hp709HP180518493 release time:2022-01-06 15:33:51

Q460b large diameter thick wall welded pipe,

The process of thick wall straight seam coiled pipe is generally rolled. If the diameter required by the customer is particularly large, it is difficult for general machinery and equipment, so it is necessary to use coiled pipe. First, after the steel plate is rolled, then weld the two rolled steel pipes. The weld is also called T-welding. Sometimes, the large diameter thick wall straight seam steel needs to roll and weld the two steel plates, Therefore, there may be two welds on a pipe body, also known as double welds. Thick wall straight seam coiled pipe has a wide range of materials. As long as it is a steel plate that can be ordered in a steel plant, it is basically OK. The main problem of the product is the welding quality. The welding quality directly determines the quality of the product, which is the main step in the thick wall rolling pipe. It is suitable for columns for bearing steel structures such as buildings, bridges, dams and offshore platforms, super long-span building structures and electric pole tower and mast structures requiring wind resistance and earthquake resistance.

Continuous pipe products are widely used in petroleum, chemical industry, natural gas transmission, pile driving, urban water supply, heat supply, gas supply and other projects. The detection of thick wall continuous pipe is mainly ultrasonic flaw detection. The longitudinal wall thickness of two cylinders should not exceed two. The butt weld of thick wall continuous pipe shall be flush with the. When the nominal diameter is larger than, back sealing welding shall be carried out in the pipe. In the process of pipe rolling, the rolling quality of pipe, Q235B rolling, Q345B rolling, large diameter thin wall rolling, large diameter thick wall rolling, stainless steel rolling, L360 rolling and 16Mn rolling were analyzed. The offer is in progress. Welcome new and old customers to consult. Prevent surface damage of steel plate.

.How is the strength grade of thick wall coiled pipe specified?

When the nominal diameter is larger than the internal seal of the pipe, and when the butt weld is flush with the pipe, it is and coiled pipe. During pipe rolling, the surface of the circuit board shall be protected from damage.

.In fact, the surface pit of the coiled pipe is almost caused by the sparse iron oxide scale on the surface of the steel plate. In general, we can apply the following methods for prevention.

Flame cutting and plasma cutting are commonly used for sheet metal blanking in our factory. The equipment used includes manual cutting, copier, semi-automatic cutting machine and NC cutting machine. Manual blanking is arbitrarily large compared to other cuts Flexible and convenient, no special supporting cutting equipment is required.

The rolled pipe shall meet the specified arc degree, end face deviation, straightness, etc.


16Mn welded steel pipeAnalysis of the individual characteristics of the market



When the pipe is rolled, the distance between the two welds shall be greater than 100mm, and the distance between the outer wall of the outer branch pipe shall not be less than 50mm.

In continuous pipe production, expanding and piercing method is widely used. Large diameter pipe rolling is drilled in the center of the blank φ 20 ~ 40mm guide hole, and then push the stamping rod from the guide hole to expand the guide hole to make the hollow blank extend reversely in the die. The capillary perforation precision is high and the capillary wall thickness is large, Q235B coiled pipe so the perforation precision is high.

The volume of coiled pipe, Q345B coiled pipe, large-diameter thin-wall coiled pipe, large-diameter thick wall coiled pipe, stainless steel coiled pipe, L360 coiled pipe, 16Mn coiled pipe and other special products have increased accordingly. With the development of domestic economic situation and the acceleration of welding and casting trend, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, but there is still a very obvious gap with foreign countries, which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10% of which the proportion of NC plasma cutting is small. In industrial production, the thermal cutting of thick wall coiled pipe generally includes gas cutting, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, which improves the machining accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology. 20 old brands, price

Product survey.Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± 13 ovality is 1% of the outer diameter, 4 6 8 10 and no more than 4 steel plate coils have standards. At present, we carry out construction according to the acceptance of standard GB / t19793-92.

Have we learned about the packaging process of the steel used? Today, let's discuss the packaging process of lower thick wall coil.

The distance between the longitudinal joints of two pipes shall be greater than 100 mm. The distance between the outer wall of the branch pipe and the weld shall not be less than 50mm.


16Mn welded steel pipeAnalysis of the individual characteristics of the market



In the production process, the hot-rolled steel pipe has the characteristics of no raw materials, that is, the mechanical properties of thick wall steel plate. In this way, the steel plate is heated first and then rolled, which softens the steel plate under great conditions, nor damage the properties such as strength, yield and tensile strength. For the wall thickness that can not be achieved by cold rolled steel pipe, the specification and model of thick wall steel pipe are added.

technological innovation.Circumferential deviation of coiled pipe, pipe groove processing and joint pair: when the pipe wall thickness is less than 6mm, it is type I weld; when the pipe wall thickness is greater than 6mm, it is type V weld; For pipes with diameter greater than 600mm and wall thickness greater than 6mm, the bottom of the pipe shall be sealed at the bottom of the pipe; In addition to the lap joint, the other type of gas coil pipe is continuous and solid V-groove butt welding. If the weld is found to be defective, the weld must be re welded. Rewelding shall not be more than twice. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has complete products and excellent quality, The price is favorable. The longitudinal weld of the winding pipe with the same cylindrical part shall not be greater than the spacing between two longitudinal joints shall not be less than 200mm. The arc length of the winding pipe calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. Let me introduce the steel plate production standard winding pipe. During the winding process, it can be divided into profiled seamless steel pipe with equal wall thickness (code D) and the wall thickness of the ground part shall not be less than the design wall thickness.

What are the advantages of thick wall coiled pipe end sizing?

Profiled seamless steel pipe is the general name of API seamless steel pipe with other section shapes except circular pipe. According to the shape and size of steel pipe cross section, profiled seamless steel pipe with unequal wall thickness (code BD) and profiled seamless steel pipe with variable diameter (code) Special shaped seamless steel pipe is widely used in various structural parts, tools and mechanical parts. Compared with circular pipe, special-shaped pipe has large moment of inertia and section modulus, and has large bending and torsion resistance, which can greatly reduce the structural weight and save energy

.After, we should prevent the surface damage of the plate. The parts with serious scars must be grinded to make transition, and the wall thickness of the grinded part shall not be less than the design wall thickness. Steel rolling pipe is an unconventional pipe, and there is no domestic standard at present. Therefore, the inspection is mainly aimed at the thickness and weld quality.

The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. It is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve metric welded pipe, rolling pipe, deep well pump pipe,Q355b large diameter thick wall coiled pipe,20# welded steel pipe, welded thin-wall pipe transformer pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of, longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes q23 q34 20#, 16 manganese, etc. Product executive standards include: GB / t50205-2001, GB / t3092-2001, etc. The products are widely used in petroleum, chemicals, natural gas transportation, pile driving urban water supply, heating, gas supply and other projects.

The diameter of large-diameter thick wall coiled pipe is generally above dn450. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, rolling pipe factory, old brand price advantage and quality guarantee! Sometimes there are two welds for large-diameter thick wall coiled pipe. Why does this happen? It is mainly due to the problems of raw materials and equipment processing. The steel plate with the required width of large-diameter welded pipe required by the customer is not produced by the steel plant, so the two plates must be welded, so this kind of weld occurs. The main problem of large-diameter thick wall coiled pipe is welding. As long as the flaw detection can be carried out, the delivery can be carried out. The relevant requirements are broader than other products. The detection of large-diameter thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same barrel section of the coiled pipe should not be more than two. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, the surface damage of the plate shall be prevented.