16Mn coilConstruction analysis

Let me introduce the standard coil produced by steel plate. In the process of rolling, the surface of the circuit board should be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.

The pipeline installation sequence shall be adopted according to the principle of zoning and subsystem. First the lower level, then the upper level, and then the difficulty. In principle,Q355b thick wall welded pipe, the pipes connected to the machine are arranged from inside to outside to reduce the impact of welding stress on the installation accuracy of the machine. The joints of indoor and outdoor pipes shall be left outdoors. Q345B thick wall continuous pipe is a widely used carbon steel material. Q345B thick wall continuous pipe with thickness greater than 10mm is widely used in drainage engineering, sewage pipeline, dredging pipeline, construction pipeline, etc. Q345B thick wall continuous pipe is a welded steel pipe product with relatively simple and flexible process. This kind of steel pipe is usually not in stock and is customized. If the quantity is small, the raw materials are not good. The main problem of Q345B thick wall continuous pipe is welding. As long as possible, delivery related requirements can be compared with other products.

.The electric contact pressure gauge is used to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of strip steel.

Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± The ovality is 1% of the outer diameter, and the quality of no more than 4 steel plate coils is greatly affected by the weld size, mainly including the comprehensive factors such as welding process parameters, flux flow, flux process performance and formed joint.

.In short, hot rolled steel pipe is a special thick wall steel pipe rolled with steel plate under heating conditions. Here, hot coiling refers to heating to coil the steel plate. Its meaning shall be determined with cold rolled steel pipe.

Steel casing means that in the process of manual hole digging pile, due to the unstable soil, it is difficult to construct reinforced concrete retaining wall, so steel retaining wall is used to protect the hole pile to prevent hole collapse and affect the construction progress and safety. High price hot rolled steel pipe of various specifications, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has timely supply and high cost performance. It has become the preferred brand for many wire products. Welcome to buy! The steel pile casing is a circular barrel hooped with iron sheet according to the size of the hole pile, and both ends are empty barrels. It can stabilize the hole wall, prevent hole collapse, isolate the surface water, guide the drill bit, protect the original ground, etc., which is generally 20-40cm larger than the pile diameter. The buried depth depends on the properties of the soil. The deviation of the plane position shall not be greater than 5cm, and the inclination shall be less than 1%. The reel is committed to the production of circumferential joints All kinds of longitudinal coils and steel penstocks are reformed on the basis of similar specifications and models of traditional coil equipment. The function of improving the parameters of the pipe rolling equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. The materials mainly include Q235, Q345, 20 #, 45 #, 35cimo and 42cimo, cold-rolled plate can be used for rolling pipe, etc. Product executive standard: GB / t50205-200, GB / t3092-2001, etc. Coiled pipes are widely used in petroleum, chemical industry natural gas transportation, pile driving, urban water supply, heat supply, gas supply and other projects.

The inspection requirements for thick wall coiled pipe treatment are that the thick wall coiled pipe is made of steel plate. The thick wall coiled pipe can be divided into coiled pipe and hot rolled thick wall coiled pipe. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The wall thickness of coiled pipe is 20mm and the outer diameter is 450-3000mm. It is rolled, welded, formed, butted, removed and reinforced directly from the steel plate. Coil processing time is short and delivery is fast.

The effect of antirust oil on thick wall coiled pipe is antirust effect, which can make the thick wall coiled pipe as smooth as new for a long time and reduce the external corrosion to it. It can also increase its sealing performance and ensure that there will be no problems when transporting fluid. In addition, it has moisture-proof performance,Q550b large diameter welded pipe, uses antirust oil to isolate the direct air of thick wall welded pipe, so it has little chance of being changed by the external situation, which increases its stable performance and safer use.

Before forming, the strip steel is leveled, trimmed, planed, surface cleaned transported and pre bent.

Extend the length of the part: 566, divide it into 24 equal parts, symmetrical and the length of each bisector from the middle to the side is: 11 110 106 10 93 84 75 66 57 0, 50 44 40 39 2.

Create brilliance.When the pipe is rolled, the distance between the two welds shall be greater than 100mm, and the distance between the outer wall of the outer branch pipe shall not be less than 50mm.

The thickness of hot-rolled thick wall coil is generally greater than 20mm, and the outer diameter range is 450-3000mm. The hot-rolled thick wall coil is rolled, welded, formed, ribbed and defect detection under the condition of steel plate heating. Sometimes the wall thickness is relatively thick and secondary heating is required. It is characterized by small outer diameter tolerance and uniform wall thickness. It is important that the hot rolled thick wall coil will not damage the properties of raw materials. The disadvantage of hot roll thick wall rolling pipe is that the treatment time is long. Hot rolled thick wall coiled pipe is widely used: cylinder, hydraulic, bridge, etc.

Have we learned about the packaging process of the steel used? Today, let's discuss the packaging process of lower thick wall coil.

In general the process of expanding the diameter of coiled pipe products can be divided into three stages. It is the preliminary rounding stage: the sector blocks are opened until all the sector blocks reach the steel pipe. At this time, the radius of each point in the steel pipe is almost the same within the step range, and the steel pipe is preliminarily rounded. The second stage is the nominal inner diameter stage: the sector starts to reduce the movement speed from the front position until it reaches the required position, which is the inner circumference position of the finished pipe with quality requirements.

technical service.Application of hot rolled steel pipe: the disadvantage of changing hot rolled steel pipe into seamless steel pipe with fixed specification and model is another major feature of hot rolled steel pipe. In the production process, hot rolled steel pipe has been widely used, bridge construction, engineering column,16Mn thick wall welded pipe, large drum and so on. Save materials and labor for the above enterprises, reduce production costs, improve the market competitiveness of finished products, and promote the development of enterprises to a certain extent. Continuous pipe is committed to producing all kinds of circumferential seam, and is reformed on the basis of the same specification and model of traditional pipe rolling equipment. The function of parameters of pipe rolling equipment is improved by 30%, which fills the gap that can not be produced by traditional steel rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm.

Starting from the service life of tools and the surface quality of pipes, the requirements are more stringent. For example, the hot furnace is divided into heating furnace and reheating furnace according to their functions. The former uses heat to the processing temperature; the latter is used to reheat the blank to the necessary processing temperature in the processing process. There are many forms of heating furnace but the ring heating furnace is mainly used. This furnace bottom, it can be heated and homogenized to the specified temperature. The furnace process is relatively slow It can rotate slowly. The blank is loaded along the diameter direction of the furnace bottom from the inlet. When it is rotated to the outlet, and the heating operation needs patience. Because if the heating operation is not standardized, cracks, folding and eccentricity on the inner or outer surface of the tube blank will only affect the product.

The arc length of the coil calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. What is the manganese content of the straight seam coil? Q345B coil, manganese is a common element in structural steel. Manganese in carbon steel is mainly added to the steel water as deoxidizer in the steelmaking process, usually in the range of 0.3-0.8%. In low alloy steel, manganese is a mixed alloy element, and the manganese content in 16Mn steel and 15MnV steel is 2-6%.

.The longitudinal weld of the same barrel part of the coiled pipe shall not be greater than 2.

The inspection requirements for thick wall coiled pipe treatment are that the thick wall coiled pipe is made of steel plate. The thick wall coiled pipe can be divided into coiled pipe and hot rolled thick wall coiled pipe. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications, welded, formed, butted, removed and reinforced directly from the steel plate. Coil processing time is short and delivery is fast.

After pushing, the elbows should be formed in this hot state, because some elbows will be distorted after improper handling, which is not allowed. In addition, after pushing the head, the outer diameter of the front end is usually large and formed by the forming die. The forming die is actually a press. It must have a set of molds, two semi arcs, one on each side. The outer diameter after forming reaches the size of the finished product.