Q355b reelShock prices can't go up or down

announcer:hp709HP180518493 release time:2021-10-31 13:10:58

Steel casing means that in the process of manual hole digging pile, due to the unstable soil, it is difficult to construct reinforced concrete retaining wall, so steel retaining wall is used to protect the hole pile to prevent hole collapse and affect the construction progress and safety. High price hot rolled steel pipe of various specifications, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe steel casing, rolling pipe factory has timely supply and high cost performance. It has become the preferred brand for many wire products. Welcome to buy! The steel pile casing is a circular barrel hooped with iron sheet according to the size of the hole pile, and both ends are empty barrels. It can stabilize the hole wall, isolate the surface water, guide the drill bit, fix the pile position, protect the original ground etc., which is generally 20-40cm larger than the pile diameter. The buried depth depends on the properties of the soil. The deviation of the plane position shall not be greater than 5cm, and the inclination shall be less than 1%. The reel is committed to the production of circumferential joints All kinds of longitudinal coils and steel penstocks are reformed on the basis of similar specifications and models of traditional coil equipment. The function of improving the parameters of the pipe rolling equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. The materials mainly include Q235, Q345, 20 #, 45 #, 35cimo and 42cimo, cold-rolled plate can be used for rolling pipe, etc. Product executive standard: GB / t50205-200, GB / t3092-2001, etc. Coiled pipes are widely used in petroleum, chemical industry, natural gas transportation, pile driving, urban water supply, heat supply, gas supply and other projects.

Today's equipment is double-sided submerged arc welding, because it goes without saying that double-sided welding is necessary here.

.Clean up the workplace and eliminate unsafe factors.

The butt joint of coiled pipe (with the same wall thickness) shall not exceed 10% of the wall thickness and not more than 2mm.

.Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and hot rolled thick wall coiled pipe.

Because the coiled steel pipe plays an important role in construction, railway construction and bridge construction, its quality standards are also more important. If you don't understand the quality specifications and standards, it is easy to have an impact. Generally, we can purchase from these aspects.

Generally, the packaging process of thick wall coiled pipe mainly includes filling, sealing and other processes, as well as related pre and post processes, such as cleaning, the process of thick wall rolling pipe shall be strict, and the production shall be carried out according to the correct methods and principles. In addition, the process of thick wall rolling pipe also includes stamping on the package. The use of mechanical packaging products can improve productivity reduce labor intensity and meet the needs of large-scale production. Thick wall coiled pipe is developed with the emergence of new packaging materials and the continuous innovation of packaging technology. It can show important value in different industries and fields.


Q355b reelShock prices can



Rolled pipe is divided into straight seam rolled pipe and T-shaped welded pipe. The pipe rolling can meet the market demand for less number and more models of welded pipes. It can be used for pipe pile, column, conveying fluid, pressure vessel, etc. The longitudinal weld of the same barrel section of high pressure and high temperature continuous pipe shall not exceed two courses, and the spacing between the two longitudinal welds shall not be less than 200mm.

Surface derusting standard: sand blasting derusting on the outer surface of steel pipe shall reach grade SA2 1 / 2 according to the requirements of GB / T 23-2008, and the depth of anchor grain on the surface of steel pipe shall be 40-100μ M steel plate rolling circle specification range steel plate rolling circle specification range: for steel pipes with an outer diameter of more than 325mm and a wall thickness of more than 20mm, at present, the large diameter of single weld can reach 1220mm, the wall thickness can reach 80 and the diameter can reach 2020mm.

Clean the iron oxide scale falling off in the process of plate drum to prevent the iron oxide scale from bonding and the surface of steel plate.

Welcome to inquire.Move the steel pipe twice to weld and reinforce the rolled pipe joint, and then transport it to the welding platform for welding.

All continuous pipe welds shall be penetration tested.

Circumferential deviation of coiled pipe, pipe groove processing and joint pair: when the pipe wall thickness is less than 6mm, it is type I weld; when the pipe wall thickness is greater than 6mm, it is type V weld; For pipes with diameter greater than 600mm and wall thickness greater than 6mm, the bottom of the pipe shall be sealed at the bottom of the pipe; In addition to the lap joint the other type of gas coil pipe is continuous and solid V-groove butt welding. If the weld is found to be defective, the weld must be re welded. Rewelding shall not be more than twice. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has complete products and excellent quality, The price is favorable. The longitudinal weld of the winding pipe with the same cylindrical part shall not be greater than the spacing between two longitudinal joints shall not be less than 200mm. The arc length of the winding pipe calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. Let me introduce the steel plate production standard winding pipe. During the winding process, the surface of the circuit board shall be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.


Q355b reelShock prices can



Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and thick wall coiled pipe. The wall thickness of coiled pipe is 20mm and the outer diameter is 450-3000mm. It is rolled, welded, formed, butted, removed and reinforced directly from the steel plate. Coil pipe processing time is short and delivery is fast Low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.

Quality department.High. Hot rolled thick wall coiled pipe is widely used: oil cylinder, hydraulic pressure, bridge, etc.

The utility model is characterized in that a T-shaped welded steel pipe needs to be hung when measuring the length. In addition, the photoelectric switch detection also has a certain error which may require a comprehensive measurement of the circumferential weld butt steel pipe.

It is to preheat rather than increase the line energy. Reel needs quality, honest business! Let's talk about our productivity.

.After pushing, the elbows should be formed in this hot state, because some elbows will be distorted after improper handling, which is not allowed. In addition, after pushing the head, the outer diameter of the front end is usually large and formed by the forming die. The forming die is actually a press. It must have a set of molds, two semi arcs, one on each side. The outer diameter after forming reaches the size of the finished product.

The continuous pipe has good characteristics and performance in use, and advanced technology is adopted. If we want to make progress and enhance competitiveness, we must have a good opportunity at present. Just like the development of the iron and steel industry, accounting for more than 1 / 4 of the world's output, there is still a certain gap with the international advanced level in terms of technical equipment, product quality and product grade, enterprise economic scale and main technical and economic indicators. The coil adopts PLC automatic system, and each part is operated on the panel. The cutting length of winding tube adopts photoelectric induction, accurate positioning and automatic cutting. Each process adopts double pump oil pressure system to ensure stable operation. The pipe rolling has different application ranges: winding pipe length: 0-1400mm, winding pipe thickness: 2-15mm, winding pipe diameter: 20-200mm, purpose: 3 inches x24x, working voltage: 380V, 50Hz. It can be used according to the specified parameters and scope, so as to ensure that it can play an important role and value in use. Large coil is durable, stable and easy to operate. The packaging process of coil includes filling, packaging, sealing and other main processes, as well as relevant pre and post processes such as cleaning stacking and disassembly. In addition, the rolling process also includes measuring or stamping on the package. Using mechanical packaging products can improve productivity, reduce labor intensity, meet the needs of large-scale production and meet the requirements of cleanliness and hygiene. With the emergence of new packaging materials and the continuous innovation of packaging technology, spiral pipe can play an important role and value in different industries and fields.

Before starting up, it is necessary to check whether the hot coil machine operates normally and fill the oil hole with oil.