Santa-CruzGalv
NaranjoIs JDG 
San-RafaelHow chemical oxidation method
There are several kinds of color q355b square tubes: high temperature oxidation method, electrochemical oxidation method, ion implantation method and gas phase cracking method.
The difference between q355b square tube and Q345A is that there are fewer impurities s and P and better low-temperature impact performance. From the welding point of view, when the impurity elements in the base metal are less, it is good for welding hot crack.
Santa-Ana.When storing Q345B square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, Q345B square pipe can not appear, weeds and other sundries should be removed in time, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products,Santa-AnaGalvanized iron pipe, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between Q345B square tube and seamless steel tube Q345B square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. Q345B square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of Q345B square tube, no deformation under high pressure, high precision,Santa-Ana120 square tube, high finish, cold bending, flaring and flattening without cracks. The chemical composition of Q345B square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.
Square pipe also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe for short. The allowable deviation of wall thickness of square pipe is f and J q355b respectively. When the wall thickness is no more than 10mm, it shall not exceed plus or minus 10% of the nominal wall thickness. Long term square pipe,Santa-Ana40 galvanized square pipe specification, rectangular pipe, seamless square pipe, galvanized square pipe galvanized pipe, 20-year-old brand, price advantage and quality guarantee! When the wall thickness is greater than 10mm, it is plus or minus 8% of the wall thickness, except for the wall thickness of corners and weld areas.
.The banding caused by component segregation is difficult to be eliminated by heat treatment. Generally, normalizing can reduce this segregation to a certain extent. Generally, normalizing can correct the segregation to the allowable level. If the banding is serious, it can be improved by multiple normalizing. It is reliable to conduct high-temperature diffusion annealing first and then normalize again, which can completely eliminate the strip, but the cost will be very high, which is difficult to achieve for the steel plate due to the surface quality.
Both internal and external welding of square pipes are carried out by American Lincoln Electric welding machine for single wire or double wire submerged arc welding, so as to obtain stable welding specifications.
The function index analysis of the square tube - the strength acts with great progress. The load on the parts is called the charge and trap load. The damage power of the square tube under the charge and trap load is called the charge and trap toughness.
Forging has many advantages in improving the plasticity of q355b square tube and improving the quality of steel, because the cast state of forged metal can be broken when forging q355b square tube. Therefore, there are forging workshops in some q355b square tube factories.
The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.
Large diameter welded square pipe for low pressure fluid transmission, Standard No.: gbt14980-1994. Representative material: q235ab grade. It is mainly used to transport low-pressure fluids, such as water, sewage, gas, air and heating steam.
Latest consultation.The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt5037-2008. The representative materials are q235bq345b and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, heating and other pipelines.
Mechanical property is an important index to ensure the end use performance (mechanical property) of square pipe, which depends on the chemical composition and heat treatment of steel. In the steel pipe standard, according to different service requirements, the tensile properties (tensile strength, yield strength or yield point, elongation), hardness and toughness indexes, as well as the high and low temperature properties required by users are specified.
With the development of economy, there are a lot of demands for project construction, which leads to the continuous increase of square pipe. The of square pipe is more complex. Great efforts should be made in the selection of raw materials, q355b square tube, q355b square tube, Q345B square tube, Q345B square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Q355b square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same but their uses are very different. The shape is different. Q355b square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt8162-199) is a square tube for general structure and mechanical structure.
Dimensional stability for high-precision square tubes, the required accuracy is high so the dimensional stability must be maintained. Due to straightening in the air and slow cooling speed, it has the effect of stabilization and will increase the number of residual square tubes in the, so it must be cooled; Reduce quenching deformation because the square tube is slender, it is easy to deform during quenching, so its deformation must be strictly controlled. Heat treatment is a key process. In the process of quenching and cooling, the cold plasticity shall be corrected in time, which is a key step to ensure the improvement of its qualification rate. Therefore, hot bath quenching or cooling in oil for a fixed time shall be carried out to propose thermal correction.
Santa-Ana.The welded joints of square pipes are subject to on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of spiral welds. If there are defects, it will automatically alarm and spray marks. The production will adjust the process parameters at any time to eliminate the defects in time.
Hardness test is to use a hard indenter to slowly the sample surface according to the specified conditions, and then test the indentation depth or size, and there is an approximate conversion relationship between material hardness value and tensile strength value. The hardness value of material can be converted into tensile strength value, which is of great practical significance.
Square tubes can be degreased with organic solvents (vinyl chloride, carbon chloride, industrial solvents, benzene, acetone, etc.), concentrated or alkaline solution. Industrial vinyl chloride is suitable for degreasing metal parts; Industrial chlorinated carbon is suitable for degreasing ferrous metal and non-metallic parts; Vinyl chloride is suitable for degreasing metal parts and non-ferrous metal parts; The industrial concentration shall not be less than 86%, which is suitable for manual scrubbing of the inner surface of the container with low degreasing requirements; 88% concentration, applicable to the concentration of some pipe fittings and porcelain rings of concentration device