El triunfo Hot
San-RafaelHow High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.
Chemical polishing: less investment in processing equipment, high speed, high efficiency and good durability. Its defects are poor brightness, gas overflow, demand for ventilation equipment and difficult heating. It is suitable for processing small batch of disordered parts and products with low brightness demand for small parts.
El triunfo Hotel.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these,El triunfo HotelHow long can the galvanized square pipe be used in the open air, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.
Empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, so they must have high hardness. Therefore, quenching, surface quenching or chemical heat treatment shall be carried out, followed by low-temperature tempering treatment.
Stainless steel q355b square pipe for fluid transportation, Standard No.: gbt12771-1991. The representative materials are 0Cr 0cr19ni 00cr19ni 00cr1 0cr18ni11nb, 0017cr17ni14mo2, etc., which are mainly used to transport low-pressure corrosive media.
Under the international investigation,El triunfo Hotel304 square tube, there has been a new improvement, which ensures that the square tube can be used for a long time. With the development of the times, square tubes are used in more and more fields. So how can we correctly choose square tubes? Next, I will introduce the process of square tubes for you.
Spray fluorocarbon paint after.
Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.
Section shape classification square tube is classified according to section shape: simple section square tube: square tube, rectangular square tube.
Encyclopedic knowledge.Structure: used as pile driving pipe and bridge; Pipes for wharf, road, building structure,El triunfo Hotel37 galvanized square pipe, etc. It is mainly used as petroleum geological drilling pipe, cracking pipe for petrochemical industry, boiler pipe, bearing pipe, high-precision structural pipe for automobile, etc.
At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.
Square tube has good machinability, good cold deformation plasticity and weldability; In addition, the toughness of steel does not decrease much during heat treatment, but it has quite high strength and wear resistance, this steel has great resistance to white spots, temper brittleness and overheating during heat treatment.
Shot blasting is a high-speed rotating impeller that throws small steel shot or small iron shot out and hits the surface of the square tube at high speed so the oxide layer on the surface of the square tube can be removed. At the same time, the steel shot or iron shot strikes the surface of the square tube at high speed, resulting in lattice distortion and deformation on the surface of the square tube and increasing the surface hardness
Information recommendation.Upper yield point (& sigma; Su): the large stress before the yield of the sample occurs and the stress decreases for the first time; Lower yield point (& sigma; SL): the small stress in the yield stage when the initial instantaneous effect is not considered.
For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.
The square tube is formed by external control or internal control roller.
El triunfo Hotel.The square tube is a low-alloy high-strength structural steel with carbon content of 0.1% - 0.25%, and the main alloy elements manganese, silicon, vanadium, niobium and titanium are added; Its total alloy content is 3%. According to the strength it is divided into four levels: 300, 350, 400 and 450MPa.
Yield point of square tube (& sigma; s): the stress of metal material with yield phenomenon when the sample can continue to elongate without increasing (maintaining constant) the force during the tensile process, which is called the yield point. If the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm2 (MPA).
The q355b square tube protective layer thickness detector is used to measure the actual thickness of the seamless q355b square tube protective layer on site. It is required that the actual thickness of the seamless q355b square tube protective layer of the seamless q355b square tube shall not be lower than the design value. When the requirements are not met, the protective layer of seamless q355b square tube can be chiseled and measured.