The cut-off position shall match the construction and site conditions, draw the determined position and mark the cut-off line with a meter ruler or other measuring tools.
Strength refers to the function that the square tube data is destroyed under static load (appropriate amount of plastic deformation or fracture), because the action form of load includes tension, compression, meandering shear and so on, because the strength is also divided into tensile strength, compressive strength, flexural strength, shear strength and so on. There is often a definite connection between various strengths. In normal use tensile strength is often used as the fundamental strength gauge.
LexingtonFayette.The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.
You can really feel that the square tube is widely used in the development, and q355b square tube factory continues to extend in the technical level, which makes the current square tube develop more widely.
.Forging has many advantages in improving the plasticity of q355b square tube and improving the quality of steel, because the cast state of forged metal can be broken when forging q355b square tube. Therefore, there are forging workshops in some q355b square tube factories.
On the basis of thermodynamic calculation, the quality assurance of square tube, rectangular tube, seamless square tube, galvanized square tube and galvanized tube is professional. New and old customers are welcome to consult during the preferential activities. The process conditions of calcium treatment of 20CrMo sulfur-containing square tube are analyzed, and the sulfur-containing gear rolled products after calcium treatment are sampled and studied. The conclusions are as follows: in order to minimize the generation of Cao in sulfur-containing square tube steel, Omega in molten steel; (O) It must be taken off to 10 & times; The rate of calcium can only be guaranteed below 10-6.
How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm2 (MPa
It is learned from the authority that if there is dirt on the outer surface of the square pipe during degreasing, it can be washed with purified water and dried naturally, then soaked with degreasing agent with a dry cloth to remove the oil, and then dried in the open air. When degreasing the inner surface of the opposite pipe, the end of the pipe can be tightly blocked with a wooden plug or closed with other. The degreasing solvent with the volume of 15% - 20% of the pipe from the other end shall be sealed with a wooden plug, placed in a flat and clean place or on a workbench with sleepers for 60-80min, and the pipe shall be rotated every 20min. If degreasing is required for stainless steel elbow, degreasing solvent shall be appropriately added to make it fully soaked. After degreasing, pour out the solvent in the pipe, dry the pipe with exhaust fan, or dry it with oil-free compressed air or nitrogen, or dry it with natural air. Large diameter pipes can be manually scrubbed with cotton cloth dipped in solvent; The square tube can also be soaked in a long tank containing solvent for 60 to 80 minutes. The concentrated pipeline and equipment of the concentrated unit can be directly pumped and circulated with 88% concentrated for pickling after all installation. Pipes that cannot circulate or are not resistant to concentrated corrosion must be degreased separately.
For transportation: water supply drainage, sewage treatment engineering, mud transportation, marine water transportation.
The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless q355b square tube. When non external force cracks appear on the surface of q355b square pipe, the crack width on the structural surface of ordinary q355b square pipe shall not be greater than 0.20mm.
Welcome calls .However, there is a large rate of end in the application of steel pipe, which is mainly due to the trouble of internal and external treatment. The first question is very crucial, and the external quality is good or bad
Classification of wall thickness square tubes are divided into super square tubes, square tubes and thin-walled square tubes according to wall thickness. Gbt6728-200gbt6725-200gbt3094-2000, JG 178-200, ASTM A500, JIS g34en10210 or technical agreement.
Steel with chromium content of more than 5% in steel and high corrosion of external medium (acid, alkali salt) is called square pipe. According to the condition in steel, square tubes can be divided into martensite, ferrite, austenite and ferrite & mdash; Austenite type, precipitation hardening square tube, according to the standard gb3280 & mdash; 92 regulations, a total of 55 regulations.
In the process of processing, the processing temperature is the key. Professional square tube, square tube seamless square tube, galvanized square tube and galvanized tube have advanced technology, strict detection, more affordable price and more preferential price. Consultation is welcome. It must be noted that the blank heating should be uniform. Perforation has a great impact on the quality. The perforation temperature of blank varies according to different materials, generally around 1200 ℃.
Word of mouth recommendation.You can really feel that the square tube is widely used in the development, and q355b square tube factory continues to extend in the technical level, which makes the current square tube develop more widely.
Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.
Tensile strength of square tube (& sigma; b): the stress (& sigma;) obtained by dividing the force (FB) borne by the sample during breaking by the original cross-sectional area (so) of the sample during stretching, which is called tensile strength (& sigma; b), and the unit is nmm2 (MPA). It represents the large capacity of metal materials under tension.
LexingtonFayette.Application: it is widely used in machinery, construction, metallurgy, agricultural vehicles, agricultural greenhouses, automobiles, railways, highway guardrails, container frames square tubes, i.e. strip coils, welding wires and fluxes. It must undergo strict physical and chemical inspection before being put into operation.
Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, the cutting will be interrupted easily due to insufficient heat.
The raw material for rolling square tube is round tube blank. For a long time, square tube, rectangular tube, seamless square tube, excellent quality and favorable price. The round tube embryo shall be cut and processed by cutting machine, and the blank with a growth of about 1m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about 1200 degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace, it should be pierced through the pressure piercer. Generally, the more common piercer is the conical roll piercer. This piercer has high production efficiency, good product quality