Stainless stee
Stainless stee
Stainless steeThe thickness of cold rolled steel strip is ultra-thin, and the thickness of hot rolled steel strip is large.
No matter under dynamic load or static load, it has higher energy absorption capacity than austenitic stainless steel which has obvious advantages and practical application value for structural parts to deal with sudden accidents such as collision, etc. Compared with austenitic stainless steel, duplex stainless steel has the following disadvantages: its universality and versatility are not as good as austenitic stainless steel. For example, its service temperature must be below 250 ℃.
.Construction materials shall be prepared and delivered to the site according to the data scheme, and shall be supplied according to the scheme.
Both ends of the steel pipe shall be cut into right angles and burrs shall be removed.
.Cold rolled non oriented silicon steel strip consists of nominal thickness (expanded by 100 times) + code a + iron loss guarantee value (the value after expanding the iron loss value when the frequency is 50Hz and the large magnetic flux density is 5T by 100 times). For example, 50a470 indicates that the thickness is 0.5mm and the guaranteed value of iron loss is & le; 7 cold rolled non oriented silicon steel strip.
410— Martensite (high strength chromium steel), good wear resistance and poor corrosion resistance.
The specification and appearance quality shall comply with the provisions of gb14975-2002 stainless steel seamless steel pipe. The steel pipe is usually 5 ~ 10m long (indefinite length) hot rolled steel pipe, 0 ~ 7m; the wall thickness is greater than 0mm, 5 ~ 8m.
The stainless steel strip is supplied in coils, also known as strip steel. It is divided into hot rolling and cold rolling, as well as ordinary steel strip and high-quality steel strip. There are many kinds of stainless steel belts! Wide use! There are: 201 stainless steel belt, 202 stainless steel belt, 301 stainless steel belt, 302 stainless steel belt, 303 stainless steel belt, 316 stainless steel belt, J4 stainless steel belt, 309S stainless steel belt, 316L stainless steel belt, 317L stainless steel belt, 310S stainless steel belt, 430 stainless steel iron belt, etc! Thickness: 0.02mm-4mm, width: 5mm-1550mm, can be customized without standard!
Deformation strengthening of austenitic stainless steel stainless steel has good cold deformation performance. It can be cold drawn into very thin steel wire and cold rolled into very thin steel strip or steel pipe. After a large amount of deformation, the strength of the steel is greatly improved, there are also superimposed Deformation induced M transition.
The design shall be carried out according to the soil, water, grooved section, load conditions and other factors of the trench, which shall be firm and reliable to prevent collapse and support, and shall not hinder the pipe laying and pipe stabilization.
Where is good.Cold drawn (rolled) seamless steel pipe: round billet → Heating → Perforation & rarr; Lead & rarr; Annealing & rarr; Pickling → Oiling (copper plating) → Multi pass cold drawing (cold rolling) → Blank tube & rarr; Heat treatment & rarr; Straightening & rarr; Hydrostatic test (flaw detection) → Mark & rarr; Warehousing.
300 series & mdash; Chromium nickel austenitic stainless steel.
Remarks: to ensure the nickel content of stainless steel strip and the mechanical properties of stainless steel strip, material certificate (Baogang material) Japan Nippon Steel Material Certificate (Nippon Steel material), SGS report, etc. can be provided.
Stainless steel has the ability of atmospheric oxidation that is, it does not rust. At the same time, it also has the ability of corrosion resistance in the medium containing acid, alkali and salt, that is, corrosion resistance. However, its corrosion resistance changes with its own chemical composition, mutual state, service conditions and environmental medium type. For example, 304 has absolutely excellent corrosion resistance in dry and clean atmosphere, but it is moved to In coastal areas, in the sea fog with a lot of salt, it will soon rust, while 316 stainless steel performs well. Therefore,Stainless steel conduit, not any kind of stainless steel can resist corrosion and rust at any time
Safety production.The steady creep rate is usually used to evaluate the long-time creep performance of materials. For the application of long-life materials, the steady-state creep rate of stainless steel pipe under high temperature and stress is the key index of the material, and can be extrapolated. The following are the test results of stainless steel pipe under different test conditions. The results show that the steady-state creep rate of stainless steel pipe sample is in the order of magnitude after creep at 550 ℃ (90mpa600 ℃ (85mpa) for 500h; when the temperature condition increases to 650 ℃ (the stress decreases to 70MPa), the creep performance of stainless steel pipe sample is good, and the steady-state creep rate is in the order of magnitude; when the temperature further increases to 700 ℃ (the temperature creep rate of 65mpa stainless steel pipe sample increased to 800 ℃ (65mpa steady-state creep rate reaches the maximum value under several test conditions, and creep fracture occurs. See for the change of steady-state creep rate of stainless steel pipe sample under several conditions. When the temperature increases, the material maintains a low level of creep rate. Under 650 ℃ 70MPa, s creep deformation rate does not increase, which shows little influence on the temperature and stress, and creep fracture occurs under this condition Compared with several other common structural materials, it can be seen that the creep performance of several materials is better than that of ordinary materials under all test conditions. After 500 hours of test, the total strain does not exceed 0.12%. The curve is relatively stable and the fluctuation is small, pipeline transportation and other working conditions with strong corrosive media. The main reason for the corrosion resistance of stainless steel pipes is the addition of a large number of elements CrNi, and Cr is the main element determining the corrosion resistance of stainless steel pipes. The electrode potential of stainless steel pipes jumps with the increase of Cr content. However stainless steel pipes are in the subsequent heat treatment During the treatment, Cr element will precipitate into the matrix in the form of carbide. On the one hand, the hardness of Cr carbide is larger than that of the matrix, and the service wear process can improve the wear resistance of stainless steel pipe. On the other hand, the precipitation of Cr containing carbide will lead to Cr Element dilution zone in some parts of the matrix, increase the number of batteries of the material, reduce the electrode potential of stainless steel pipe and reverse the corrosion Therefore, in order to obtain good corrosion and wear resistance, the combination of mechanical properties and corrosion resistance of stainless steel pipe materials needs to be considered. At present, some scholars have studied the effects of austenitizing temperature and time, tempering temperature and time on the mechanical properties of stainless steel pipe by heat treatment to change the corrosion resistance of stainless steel pipe And corrosion resistance, it is found that austenitizing temperature can change mechanical properties, while tempering temperature has a great effect on the corrosion resistance of materials. Appropriate austenitizing temperature and tempering temperature can improve the corrosion and wear resistance of materials. Some scholars use surface treatment to improve the corrosion and wear resistance of materials,304 stainless steel pipe, It is concluded that low-temperature nitriding forms a diffusion layer on the surface of the material, improves the wear resistance of the material, interacts with Cr and chemically stable phase 07-fe3n to improve the corrosion resistance of the material.
Restate the quality of stainless steel pipe,Stainless steel bowl with magnetic, such as stainless steel pipe, we promise & ldquo; 8 chromium and 18 nickel & rdquo; Penalty for false and provide quality inspection report and certificate of conformity.
303— Add a small amount of sulfur and phosphorus to make it easier to cut.
.& Ge; about 40 thickness: cold rolled 2B plate (0.09 & mdash; 0mm); hot rolled industrial plate No.1 (3-50mm) medium plate, chemical plate and high temperature plate; width: 5mm --- 850mm steel strip; 1000, 1211250, 1500, 1800 and 2000mm coil plate and flat plate surface: 2B smooth surface, BA (6K) mirror, 8K mirror, 9K mirror wire drawing surface and frosted surface.
After the stainless steel pipe is completed, it must be moved, moved and moved for a long distance. If there is no bag, there will be scratches and scratches on the surface, which will affect the appearance of the surface.
Since last year foreign countries have frequently carried out & ldquo; Double inverse & rdquo; This has a great impact on China's stainless steel casting industry. Export is a large part of the development of China's stainless steel industry and occupies a huge market share in its industrial development. In the face of the current economic downturn and slow development speed, the development of China's stainless steel industry should continuously improve product quality, Better develop overseas trade and deal with trade protectionism, combine products with environmental protection, energy resources and cultural environment, and improve the competitiveness of stainless steel products. Only in this way can we achieve an invincible position in foreign trade.