45# large diameter thick wall coiled pipeProduct classification related knowledge

announcer:hp709HP180518493 release time:2022-03-19 12:17:39

In order to make you better understand the installation method of coiled pipe, the following coiled pipe factory will introduce the installation method of coiled pipe: pipe hoop is used, and raw silk belt, white hemp wire, pipe expander, handle and other tools are used to connect coiled pipe and pipe fittings. This method may need repeated debugging due to the great influence of human factors. In addition, when the materials of coiled pipes and pipe fittings are different, due to their different thermal coefficients, leakage may occur when cold and hot water are used alternately.?

The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.

.Qualitative properties for example, the strength of steel is greater than that of its main constituent element iron. Professional hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory safety, environmental protection and economy! The products are exported to foreign countries and are deeply trusted. The physical properties of the alloy such as density, may be similar to the constituent elements of the alloy. High quality thick wall steel plate coil, but the tensile strength and shear strength of the alloy are usually very different from the properties of the constituent elements and the atomic arrangement in the simple substance.

, low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.

.Thickness detection thickness detection is very simple, the adhesion and impact strength of the coating will be reduced. For serious internal pitting corrosion, it can not only rely on the high-strength impact of large particles of rinse agent, but also remove corrosion products with small particles. Reasonable ratio design can not only slow down the speed of pipeline and nozzle (propeller) rinse agent. Wear and tear, and the rate of rinsing agent can be greatly improved. Generally,Q235B welded pipe, the particle size of metal particles is 2 - 9mm, and the particle size of metal sand is 1 - 2mm, of which 3 - 5mm is a common component. The sand shot ratio is usually 4 to 9.

The latter stage is called unloading regression. At this time the sector continues to retract from the circumferential position of the rewind pipe before rewinding, and will eventually reach the initial expanding position, which is the small shrinking diameter of the sector required by the expanding process. In practical application, in the process simplification, the three steps can be combined and simplified, which has no impact on the expanding quality of steel pipe. How to calculate the weight per meter of steel coil? Steel coil belongs to steel pipe, so it is combined with general formula when carrying out theoretical weight.


45# large diameter thick wall coiled pipeProduct classification related knowledge



The pipe volume is huge, the production site environment is complex, and the measurement cannot pass through the lower support bench of the steel pipe. This operation is convenient and the measurement accuracy is within & plusmn; Within 10mm, repetition accuracy ≤ 5mm. Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and hot-rolled thick wall coiled pipe.

Thick wall coiled pipe is not only used to transport fluid and powdery solids, exchange heat energy, mechanical parts and containers, but also a kind of economic steel. Building structural grid with steel can reduce weight, save metal by 20 ~ 40%, and realize industrialized mechanized construction. Building highway bridges with steel can not only save steel and simplify construction, but also greatly reduce plot, investment and maintenance Maintenance cost. Thick wall coiled pipe is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is mainly used in tap water engineering, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products of development. It is used for gas transmission: gas,20# reel, steam and liquefied petroleum Gas: used as pile driving pipe, bridge, wharf, road, building structure pipe, etc.

Circumferential deviation of coiled pipe pipe groove processing and joint pair: when the pipe wall thickness is less than 6mm, it is type I weld; when the pipe wall thickness is greater than 6mm, it is type V weld; For pipes with diameter greater than 600mm and wall thickness greater than 6mm, the bottom of the pipe shall be sealed at the bottom of the pipe; In addition to the lap joint, large diameter thick wall rolling pipe,Q235B welded steel pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has complete products and excellent quality, The price is favorable. The longitudinal weld of the winding pipe with the same cylindrical part shall not be greater than the spacing between two longitudinal joints shall not be less than 200mm. The arc length of the winding pipe calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. Let me introduce the steel plate production standard winding pipe. During the winding process, the surface of the circuit board shall be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.

packing.The butt joint of coiled pipe (with the same wall thickness) shall not exceed 10% of the wall thickness and not more than 2mm.

Meet the following requirements: 1. The longitudinal joint of butt joint shall not be greater than 10% of the wall thickness plus 2mm, and shall not be greater than 3mm. 2. The longitudinal joint of joint 200mm away from the pipe end shall not be greater than 2mm. 3. Other parts shall not be greater than 1mm. 4. The vertical deviation between the end face of coiled pipe and the center line shall not be greater than percent of the outer diameter of pipe and shall not be greater than 3mm. The straightness deviation shall not exceed 1mm / m. 5 the weld cannot be double-sided molded coiled pipe. When the nominal diameter is greater than or equal to 600mm, it is recommended to seal and seal in the pipe. In order to obtain better uniform cleanliness and roughness distribution, which may cause the anti-corrosion layer to become thinner at the peak of the cloud path. At the same time, because the cloud path is too deep, bubbles are easy to form in the process, which seriously affects the performance of the layer.

The diameter of thick wall coiled pipe is usually higher than dn450. Thick wall coiled pipe is sometimes two welds. The reason why this happens is mainly due to the problems of raw materials and equipment processing. The steel plate with the required width of welded pipe required by the customer is usually not produced by the steel plant, so two plates need to be welded, so the weld will occur.


45# large diameter thick wall coiled pipeProduct classification related knowledge



Steel plate materials mainly include Q235, Q345, 20, 45, with 16 manganese and 16 manganese capacity. Generally, cold rolled plate can be used for pipe winding. Like oil, chemicals, natural gas transportation, piling and urban water supply, heating, gas supply and other projects can be customized! The required thickness and length can be adjusted as required! The rolling pipe weld is a double-sided weld. Two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.

Welcome calls .After, we should prevent the surface damage of the plate. The parts with serious scars must be grinded to make transition, and the wall thickness of the grinded part shall not be less than the design wall thickness. Steel rolling pipe is an unconventional pipe, and there is no domestic standard at present. Therefore, the inspection is mainly aimed at the thickness and weld quality.

All the welded welds are subject to on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of spiral welds. If defective

If the particle size of straight seam coiled pipe is too small, the adhesion and impact strength of the coating will be reduced. For serious internal pitting corrosion, it can not only rely on the high-strength impact of large particles of rinse agent, but also remove corrosion products with small particles. Reasonable ratio design can not only slow down the speed of pipeline and nozzle (propeller) rinse agent. Wear and tear, and the rate of rinsing agent can be greatly improved. Generally, the particle size of metal particles is 2 - 9mm, and the particle size of metal sand is 1 - 2mm, of which 3 - 5mm is a common component. The sand shot ratio is usually 4 to 9.

.The effect of antirust oil on thick wall coiled pipe is antirust effect which can make the thick wall coiled pipe as smooth as new for a long time and reduce the external corrosion to it. It can also increase its sealing performance and ensure that there will be no problems when transporting fluid. In addition, it has moisture-proof performance, uses antirust oil to isolate the direct air of thick wall welded pipe, so it has little chance of being changed by the external situation, which increases its stable performance and safer use.

In the production process, the hot-rolled steel pipe has the characteristics of no raw materials, that is, the mechanical properties of thick wall steel plate. In this way, the steel plate is heated first and then rolled, which softens the steel plate under great conditions, which will not affect the material quality, nor damage the properties such as strength, yield and tensile strength. For the wall thickness that can not be achieved by cold rolled steel pipe the specification and model of thick wall steel pipe are added.

The quality of steel rolling pipe is greatly affected by the size of weld, mainly including welding process parameters, shape and position parameters of welding wire, flux flow, flux process performance, forming joint and other comprehensive factors.