The general delivery length of square pipe is 3200mm-13000mm, mostly 65000mm and 13000mm. The square tube is allowed to deliver short and non fixed length products not less than 2300mm or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus 10% of the nominal wall thickness when the wall thickness is not greater than 10mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed 8% of the total delivery. For square tubes with a theoretical weight greater than 20kgm, it shall not exceed 5% of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics, we can correctly select the appropriate application field, In this way, the use efficiency of square tube can be improved. Next, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade 8 ~ 9. If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).
Stainless steel q355b square pipe for fluid transportation Standard No.: gbt12771-1991. The representative materials are 0Cr 0cr19ni 00cr19ni 00cr1 0cr18ni11nb, 0017cr17ni14mo2, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.
At present, square tubes also have many good properties, strong corrosion resistance and heat resistance, and are widely used in many scientific and technological fields. Therefore, even so, wise people still do not stop studying the surface adhesion resistance of square tubes. Square tubes in the future will have better performance and make more important contributions to development.
.The painting of the square tube has to go through a process, which requires us to conduct comprehensive consideration and analysis. In particular, the quality and level of the paint and the relevant technical level deserve our attention. Note that the square tube should not be used immediately after painting, but should be placed for a period of time and wait until the paint is dry!
Now, with the continuous development of q355b square tube, its use is becoming more and more extensive, we still look forward to the development of q355b square tube in the future.
Q355b square tube is a kind of hollow square section steel square tube, also known as hollow cold-formed section steel. It is a section steel with square section shape and size made of hot-rolled or cold-rolled strip or coil plate after cold bending and high-frequency welding.
At present, researchers at home and abroad have carried out experimental discussion on the anti adhesion of square tube surface. So far, there is still a lack of research on surface adhesion, there is no systematic and perfect theory to guide the preparation of anti adhesion inner surface of pipeline, based on the solid-liquid interface adhesion work theory and smooth solid surface model, this paper analyzes the spreading process on machined rough surface, studies the dynamic movement characteristics of solid-liquid vapor phase line, directly analyzes the adhesion process, and establishes a line spreading model based on small system energy, It provides theoretical guidance for the preparation of anti adhesion surface of pipeline.
After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.
The butt joint between the head and tail of square pipe and strip steel adopts single wire or double wire submerged arc welding, and automatic submerged arc welding is adopted for repair welding after rolling into square pipe.
Administration.When cutting the sample, the surface of the sample shall not be damaged, the properties of the metal shall not be changed due to heating or cold processing, and the edges at the section shall be rounded.
Avoid contact with pollutants such as oil and copper when storing square tubes.
After time, the workpiece forms an oxide film with a fixed thickness and presents various colors. Chemical oxidation method is to form various film colors in a specific solution at temperature and time; Because of the law & rdquo; More, but to maintain the color of the product, the reference electrode must be used. Electrochemical method is to form the color of chloride film with fixed thickness in specific electrolyte at temperature, voltage and time. This process is mature and widely used. Ion implantation method is to vaporize ions in vacuum and deposit them on the surface of q355b square tube, which is suitable for mass production. The process of gas phase cracking is more complex and less used in industry. Square tube has long been widely used in mechanical industry. When the square pipe is cut automatically, when the square pipe is hoisted to the gas cutting platform the distance difference between the two ends of one side of the pipe and the guide rail shall be adjusted within 5mm. During semi-automatic cutting, the guide rail shall be placed on the plane of the cut pipe, and then the cutting machine shall be placed on the guide rail gently.
Among them, q355b square tube is divided into process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welded square pipe.
reform.The function index analysis of the square tube - the strength acts with great progress. The load on the parts is called the charge and trap load. The damage power of the square tube under the charge and trap load is called the charge and trap toughness.
Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.
Stainless steel q355b square pipe for fluid transportation, Standard No.: gbt12771-1991. The representative materials are 0Cr 0cr19ni 00cr19ni 00cr1 0cr18ni11nb, 0017cr17ni14mo2, etc., which are mainly used to transport low-pressure corrosive media.
Churavesta.Q355b square pipe for mining fluid transportation, Standard No.: gbt14291-2000. The representative material is Q235 grade B steel which is mainly used for coal mine air pressure, drainage and vertical shaft gas drainage straight seam q355b square pipe.
Effective treatment of square tube coating & ldquo; Surface defense line & rdquo; Surface technology and measures square tube coating is used as the back course & ldquo; Surface defense line & rdquo; The surface treatment technologies and measures can be carried out on the basis of other surface treatment technologies or processes. Here's the & ldquo; Surface treatment before coating & rdquo; It refers to all treatment measures for preparation for coating or joint protection with coating. Therefore, the surface treatment before coating is also called coating surface pretreatment.
Brinell hardness, Rockwell hardness and Vickers hardness are commonly used.