NaranjoIs JDG 
San-RafaelHow The painting of the square tube has to go through a process, which requires us to conduct comprehensive consideration and analysis. In particular, the quality and level of the paint and the relevant technical level deserve our attention. Note that the square tube should not be used immediately after painting, but should be placed for a period of time and wait until the paint is dry!
Now in many construction projects, we can see the shadow of q355b square tube, because q355b square tube is quite hard in hardness, and the performance and quality of deformation, stamping, cutting and other processing are based on hardness, which is also the guarantee of mechanical properties. Based on the above, it is very important to test the hardness of q355b square tube.
Rolando.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.
Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.
.The cut-off position shall match the construction and site conditions, draw the determined position and mark the cut-off line with a meter ruler or other measuring tools.
It is mainly caused by the fact that the square pipe body has no cover, the covering protection is not ideal, and there is no support, partly due to the excessive number of stacking layers, and most coastal areas belong to marine climate, with large annual rainfall, high air humidity, ponding in the square pipe and the square pipe. The protection shall be: if the bare pipe or pipe needs to be stored for a long time, it shall be protected with an uncovered object from the beginning of storage to avoid rusting, layer aging, edge warping and other phenomena of the square pipe.
When cutting the sample, the surface of the sample shall not be damaged, the properties of the metal shall not be changed due to heating or cold processing, and the edges at the section shall be rounded.
The difference between q355b square tube and Q345A is that there are fewer impurities s and P and better low-temperature impact performance. From the welding point of view, when the impurity elements in the base metal are less, it is good for welding hot crack.
High density may not be obtained by simple pressurization, and then made by hot rolling cold rolling or cold drawing. Square pipe plays an important role in steel pipe industry.
Energy costs.The square tube shall be painted correctly. Professional square tube, square rectangular tube seamless square tube, galvanized square tube and galvanized square tube have stable, the square tube will be corroded. The correct paint shall also be selected during painting, So as to ensure that the square tube will be better and better in future use. The square tube is widely used in the soul. Each kind of square tube has different functions for the other tube. We choose the right way and different square tubes, which can increase the performance of the square tube and be applied to different fields. Let me briefly introduce the lower tube.
Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV). Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.
Large diameter welded square pipe for low pressure fluid transmission, Standard No.: gbt14980-1994. Representative material: q235ab grade. It is mainly used to transport low-pressure fluids, such as water, sewage, gas, air and heating steam.
It is feasible to use the theory to calculate static structures, such as warehouses, houses and bridges, but it is not suitable for moving components such as wheels. At this time, people often use the plastic theory. The research of the plastic theory can be traced back to 1914. In 1975, the European Design Association formulated a plastic design code, which is mainly used for static load plane beams and frame structures subjected to bending stress The solution is as follows: for high-rise buildings, more detailed calculations are needed.
Range.Q355b square tube, the selected die material, has obvious hardening in the deep drawing process, resulting in many hard metal points resulting in adhesion. Special products such as professional square tube, square rectangular tube, seamless square tube, galvanized square tube and galvanized tube are 20-year-old brands, with advantageous price and guaranteed quality. It makes the surface of workpiece and die easy to scratch and wear, so tool steel for general die can not be used.
It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation,RolandoSquare steel rectangular tube,Rolando2 galvanized square pipe, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.
After perforation,RolandoQ235A square tube, the round tube blank is successively rolled by cross rolling, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening the steel pipe
Rolando.When cutting the sample, the surface of the sample shall not be damaged, and the edges at the section shall be rounded.
Q355b square tube is a kind of hollow square section steel square tube, also known as hollow cold-formed section steel. It is a section steel with square section shape and size made of hot-rolled or cold-rolled strip or coil plate after cold bending and high-frequency welding.
The performance advantage of square tube after calcium treatment requires not only high strength, but also good machining performance. For sulfur-containing square tube, sulfur can improve the machinability of steel