Electric fusion connection: when the pipe fittings leave the factory, the resistance wire is buried in the pipe fittings to make electric fusion pipe fittings. At the construction site, only the plug of the special welding instrument and the socket of the pipe fittings need to be connected. The inner body of the pipe fittings melts the outer plastic of the pipe fittings and the inner plastic of the pipe fittings to form a reliable connection, and combines the timing methods such as special digital timekeeper and installation indicator hole.
Electric fusion connection: when the pipe fittings leave the factory, the resistance wire is buried in the pipe fittings to make electric fusion pipe fittings. At the construction site, only the plug of the special welding instrument and the socket of the pipe fittings need to be connected. The inner body of the pipe fittings melts the outer plastic of the pipe fittings and the inner plastic of the pipe fittings to form a reliable connection, and combines the timing methods such as special digital timekeeper and installation indicator hole.
.Clean up the workplace and eliminate unsafe factors.
The wall thickness of general coiled pipe is 20mm and the outer diameter is 450-3000mm. It is made of steel plate by direct rolling, Cut into blanks about meters in length. However the round pipe shall be cut by cutting machine, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. Docking and strengthening. Coil pipe processing time is short and delivery is fast Low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.
.The influence of welding process parameters on welding current mainly includes two aspects: according to the production characteristics of spiral steel pipe, small welding current is usually used for internal welding
When the nominal diameter is greater than or equal to 600mm, back welding shall be carried out in the pipe.
: 90% of the developed thick wall coil processing industry is CNC cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. In industrial production, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, plasma cutting has developed rapidly. Professional hot-rolled steel pipe, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, rolling pipe factory, high pressure rating, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. With the rapid development of computer and digital technology, NC cutting has also expanded and improved the processing accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology. The large-scale rolling pipe factory of rolling pipe, t-welded rolling pipe, flaw detection welding rolling pipe, 16Mn rolling pipe, Q345B rolling pipe and special-shaped rolling pipe, and the t-welded rolling pipe, 16Mn rolling pipe, Q345B rolling pipe and special-shaped rolling pipe produced by the rolling pipe factory are exported to major engineering buildings at home and abroad.
Thick wall coiled pipe is usually higher than dn450. Thick wall coiled pipe is sometimes two welds. Why does this happen mainly because of raw material problems and equipment processing problems? The steel plate with the required width of welded pipe required by the customer is usually not produced by the steel plant, so two plates need to be welded so the weld will occur. The main problem of thick wall coiled pipe is welding. As long as flaw detection can be carried out, the requirements related to delivery are wider than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector. The longitudinal weld on the same cylindrical part of the coiled pipe shall not be greater than 2. When the coil pipe is butt welded, the corresponding parts shall be flushed to. When the nominal diameter is larger than the inner seal, 20#, 35#, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory and other related businesses. Merchants who hope to have this business please. The steel plate with the required width of welded pipe required by customers is generally not produced by the steel factory, so the two plates must be welded, so this kind of weld occurs. The main problem of thick wall coiled pipe is welding. As long as the flaw detection can be carried out, the delivery can be carried out. The relevant requirements are broader than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. High cost. Hot rolled thick wall coiled pipe is widely used: oil cylinder, hydraulic pressure, bridge, roller, etc& amp; amp; quot; Compared with seamless steel pipe, thick wall coil has the disadvantages of low cost, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Quality department 3 editing of welding process and welded pipe type thick wall coiled pipe is made of steel plate or steel strip after bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Objective knowledge packaging strategy thick wall steel plate coil - thick wall steel plate coil price thick wall coil is formed by bending steel plate or steel strip, and the electrical model is
The main purpose of preheating is to reduce the cooling rate of welded joints and preheat temperature. As can be seen from the table, preheating can reduce the cooling rate, but basically does not affect the time spent at high temperature, which is ideal. Therefore, when welding thick wall coils with hardening trend, the main technical measure to reduce the cooling rate and hardening trend is preheating rather than increasing the line energy. Plasma cutting of thick wall coiled pipe is more effective than gas cutting
Process inspection.The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. According to the purpose, it is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, rolling pipe, deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of, longitudinal ring coil pipe and steel pressure pipe and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes Q235, Q345, 20, 16 manganese, 16 manganese capacity, etc. Product executive standards include: GB / t50205-2001, GB / t3092-2001, etc. The products are widely used in petroleum, chemicals, natural gas transportation, pile driving, urban water supply, two longitudinal welds are allowed, and the spacing shall be greater than 200mm.
Recently, with the rapid development of excellent strip continuous rolling production and the progress of welding and inspection technology, the weld quality has been continuously improved, and the technology of welded pipe has also been continuously improved, and the application field is relatively wide, so as to gradually replace the seamless steel pipe. The main one is the technological development of welded pipe. Our welded pipe is made of steel plate or strip steel and welded after crimping. It is generally a welding process, which improves the production efficiency and service quality of welded pipe.
In short, the use standard of coiled steel pipe is very important, and the above points can be reasonably explained. For the information of our rolled steel pipe, let's simply say so much today. If you need it, you can directly consult our manufacturer.
The pipe volume is huge, the production site environment is complex and the measurement cannot pass through the lower support bench of the steel pipe. This operation is convenient and the measurement accuracy is within & plusmn; Within 10mm, repetition accuracy ≤ 5mm. Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and hot-rolled thick wall coiled pipe.
Excellent quality.The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.
Grounding current, while external welding uses a larger welding current. However, when the welding current is large, the effect of welding rod is intensified, and the melting amount of welding wire is also increased accordingly, the weld reinforcement is increased, the weld formation is deteriorated and the edge transition is poor.
The pipe volume is huge, the production site environment is complex, and the measurement cannot pass through the lower support bench of the steel pipe. This operation is convenient and the measurement accuracy is within & plusmn; Within 10mm, repetition accuracy ≤ 5mm. Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and hot-rolled thick wall coiled pipe.
.In general, the hot coil pipe is mainly committed to the production of all kinds of circumferential seam and longitudinal ring coils and steel penstocks. It is reformed on the basis of traditional coil equipment and similar specifications and models, so that all parameters of the hot coil pipe can be improved filling the gap that the original traditional coil equipment can not produce. In addition, in terms of processing technology the hot coil pipe needs attention. The following matters are required: before processing, the hot coil pipe needs to be familiar with the technical requirements of paper, process material properties and other related aspects, select an appropriate hot coil machine, determine whether the cold coil, warm coil or hot coil, and then operate.
The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.
The distance between the two longitudinal slits of the reel assembly shall be greater than 100mm. The distance between the outer wall of the branch pipe and the weld shall not be less than 50mm.