◆ stainless steel and alloy tool steel (C content is expressed in thousandths), such as 1 thousandth of 1Cr18Ni9 (i.e., stainless C & LE); 0.08%, such as 0Cr18Ni9, ultra low carbon C & le; 0.03% if the international stainless steel mark, the American Iron and Steel Institute uses three digits to mark various standard grades of malleable stainless steel. Among them, austenitic stainless steel is indicated by numbers of 200 and 300 series, and ferritic and martensitic stainless steel is indicated by numbers of 400 series. For example, 30, 316 and 310, ferritic stainless steels are marked with 430 and 446, martensitic stainless steels are marked with 4420 and 440C, duplex (austenitic ferrite), stainless steels, precipitation hardening stainless steels and high alloys with iron content less than 50% are usually named by patent name or trademark.
According to different metallographic structure of stainless steel, martensitic stainless steel pipe, austenitic ferritic stainless steel pipe, etc.
.Continuous casting shall be adopted for stainless steel pipe fittings, so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.
When the stress exceeds the limit, even if the stress no longer increases, the steel or sample continues to have obvious plastic deformation. This phenomenon is called yield. Professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe ensure quality service and quality. Your satisfaction is our pursuit! Welcome to inquire The small stress value when yielding phenomenon occurs is the yield point. Let PS be the external force at the yield point s and fo be the cross-sectional area of the sample, then the yield point & sigma; s = PS / fo (MPA), MPa is called MPa, which is equal to n (Newton) / mm (MPA = 106pa, PA: Pascal = n / m.
.Buttress shall be set at the turning of T-interface pipeline in vertical or horizontal direction. The size of buttress shall be determined through calculation according to pipe diameter, corner, working pressure and other factors.
Cold formed alloys can be cut and cold formed. However, due to its high strength and hardness, the alloy needs cold forming more than austenitic steel. Because of its high strength, springback should be fully considered.
6 Density 400 & rdquo; Density of series: 93310s, 309S and 316316 density stainless steel coils of 30323042001 are divided into Austenitic, ferrite, martensite, duplex (ferrite austenite) stainless steel cold rolled coil and stainless steel hot rolled coil.
The method is that the heated tube blank is placed in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipes with smaller diameter.
Some reasons for product composition ratio: in order to reduce the production cost reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, especially in the environment containing chloride ions. Stress corrosion is a prominent problem that ordinary austenitic stainless steel is difficult to solve.
National standard thickness of stainless steel pipe. Stainless steel pipe is a brand of stainless steel produced according to American ASTM standards. Before the national standard thickness of stainless steel pipe, there are stainless steel pipe national standard thickness national standard wall thickness table product name specification material price (yuan ton) rise and fall welded pipe 6 points 5mm (& phi; 275mm) 3850 + 30 welded pipe 1 inch 0mm (& phi; 330mm)
Stainless steel pipe appeared in Foshan, Guangdong Province in the tenth generation of the last century. With the rapid development of science and technology in recent decades, stainless steel pipe production is all over the country. Stainless steel pipe is more and more widely used. But in fact, do not know much about the classification and application of stainless steel pipes. Take stainless steel pipe for example.
The Ministry of Commerce announced that the European Commission announced that it would impose a final anti-dumping duty of 43% ~ 79% on China's stainless steel seamless steel pipes exported to Europe including many people in the industry, which made the steel pipe enterprises already under the pressure of domestic and foreign troubles worse.
Pursuit of excellence.Batch size: a small number of single batch products will affect the unit price.
The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening outer thickening or inner and outer thickening).
— General model; 188 stainless steel. The GB brand is 0Cr18Ni9.
.Theoretical weight: Cr Ni austenitic stainless steel austenitic stainless steel (kg / M) s-wall thickness (mm)
The process of this product determines its limited performance. Generally, the precision of seamless steel pipe is low: uneven wall thickness, low brightness on the inner and outer surface of the pipe, high sizing cost, and there are pockmarks and black spots on the inner and outer surface, which are not easy to remove; its detection and shaping must be processed offline. Therefore, it embodies its advantages in high pressure, high strength and mechanical structure materials.
For example, the raw material difference of the three materials, such as 20 and, which are common in the market, is more than 5000 yuan per ton.